Blog spletnega mesta

vidno vsem

- ob temeljitem poznavanju vsebine, pri kateri želim dokaze,

- pri jasno podanih kriterijih za dokazovanje znanja,

- pri sprotnem preverjanju znanja


    Slika od Syed Hassan
    od Syed Hassan - ponedeljek, 23. november 2020, 17:08
    vidno vsem

    When you're fixing cladding over an electrical installation or fitting, you can't just clad over the top. To start with, by law each association must be accessible for examination and testing upkeep. Also, second, there's a danger of curving, overheating, or electric shock on the off chance that you cover the zone or attempt to confine the association yourself without following the correct technique. Continuously utilize a certified circuit repairman in case you're in any uncertainty.

    Picking your cladding 

    Cladding comes in different lengths and thicknesses yet all utilize the strategy for tongue-and-section joints. You'll discover an assortment of notable cladding frameworks. Some are made of genuine wood, some are generally excellent impersonations. Some need fixing with pins, others simply need glue. External cladding is the best option of all. 

    Before you start 

    Open up your timber and external cladding and untruth it levels on its side. Store the timber in the room being clad fourteen days before introducing it. This enables the wood to adapt and shrivel before being fixed. Cautiously eliminate avoiding board, dado rails, and picture rails, and coving from the wall if fundamental. You may need to change flexible lines to radiators by presenting them by the thickness of the boards and cladding. 

    Joining secures 

    A timber secure is a bit of treated, sawn wood used to help the cladding. You'll have to nail wood secures to the wall or roof before you join your cladding. Be that as it may, if the territory is acceptable and level, essentially utilizing solid cement might be sufficient. Choose where to situate hefty things, for example, radiators or hand bowls. Connect more extensive secures to the wall and hang the thing from these. In case you're cladding over mortar the boards should gauge 22mm high x 50mm wide. For cladding over a block or square work secures should be 38mm high x 50mm wide. Join secures to the wall or roof at 90 degrees to the cladding boards, as a rule at 400mm spans. If the boards run evenly, position the most minimal simply over the degree of the evading. When fitting secures to a roof, ensure they're safely appended to the joists. Denoting the situation of every joist over the roof will make your employment simpler. 

    Setting up the cladding 

    Sanding and applying finish to the cladding. Before you append the cladding to the boards, ensure the outside of the cladding is smooth and prepared for you to apply your picked finish. Sand the outward essence of the cladding and vacuum off residue. At that point clean the surface off with a buildup-free fabric hosed with white soul. In case you're arranging a water-based completion (matt completion paint, for instance) hose the material with water before cleaning the surface off. 

    Apply two layers of your completion to the front and back of the sheets to help forestall the timber misshaping. Try not to cover within the notch or back of the tongue. Apply the last covers just when you've cut and fixed the sheets. 

    Stamping and cutting 

    • Imprint the sheets at your picked tallness with a blade or pencil. 

    • Imprint points of 45 degrees (or different points) with a flexible blend square. It's essential to get the points right so the cladding fits properly appropriately. 

    • Saw off the end - this segment is squandered. Utilize a similar method to stamp and slice the sheets to length. Eliminate any splinters with sandpaper. 

    • Apply two layers of your completion to the front and back of the sheets to help forestall the wood contorting. 

    Fixing cladding 

    Pick your beginning stage. Working from left to right, place the primary board against the wall. Utilize a soul level to check the board is level. Drive pins, simply away from the depression, through the board into the strip. At that point drive pins through the tongue - one for every board.  Spot the following board in position. Utilize an off-cut of board 50mm wide - remove the depression side to secure the tongue of the new board while you slide it into place with delicate mallet taps. Fix with pins through the tongue. 

    Wrapping up 

    • Fit moldings. These ought to be prefinished similarly to the cladding. 

    • Fix set up with board glue. 

    • Cautiously fill any pin openings with a wood filler that coordinates the shade of the wood. 

    • Try not to spread the filler around something over the top. At the point when the filler is dry, softly rub it down. 

    • At last, apply a couple of more layers of finish.


      Slika od Urška Avbreht
      od Urška Avbreht - ponedeljek, 23. november 2020, 16:56
      vidno vsem

      Uporabila sem že Prezi. Želim si preizkusiti še Flashcard delux in Kahoot.


        Slika od wijaya liu
        od wijaya liu - ponedeljek, 23. november 2020, 16:36
        Slika od asdwd adwsd
        od asdwd adwsd - ponedeljek, 23. november 2020, 16:08
        vidno vsem
        [ Spremenjeno: ponedeljek, 23. november 2020, 16:08 ]


          Slika od وفاء محمد
          od وفاء محمد - ponedeljek, 23. november 2020, 16:04
          Slika od grace bxy
          od grace bxy - ponedeljek, 23. november 2020, 16:01
          Slika od وفاء محمد
          od وفاء محمد - ponedeljek, 23. november 2020, 15:59
          Slika od intan kesum
          od intan kesum - ponedeljek, 23. november 2020, 15:58
          Slika od وفاء محمد
          od وفاء محمد - ponedeljek, 23. november 2020, 15:54